Early Black Friday: $40 off BuildBoxFree US shipping
Get BuildBox

Kids workbenches and tool benches

DIY Kids Workbench Ideas: 7 Builds From Common Materials (and When Buying Makes More Sense)

By Kids Tool Sets editorial team Published Last updated:

Thoson BuildBox kids tool set opened into a child-height workbench and seat, shown as a ready-made alternative to a homemade DIY kids workbench
In this guide
  1. Quick answer
  2. What a DIY kids workbench needs to do
  3. Before you build: measure, plan and pick a spot
  4. 7 DIY kids workbench ideas from common materials
  5. Materials and finishes: what to use and what to skip
  6. DIY kids workbench safety checklist
  7. Building the workbench together
  8. Stocking the bench: tools, parts and storage
  9. When buying is better than building
  10. Build vs buy at a glance
  11. Keeping a homemade workbench useful as kids grow
  12. Frequently asked questions

A DIY kids workbench can be as simple as a cube shelf turned on its side with a plywood top, or as involved as a weekend plywood-and-2x4 build. The best homemade versions sit between your child’s waist and elbow height, have rounded edges and a raised lip so parts don’t roll off, and stay put when a kid leans on them. If you don’t have the tools, time or wall space, a ready-made toolbox that opens into a bench gives you most of the benefit in a few minutes.

Below are seven builds that use materials you can find at a hardware store, a thrift shop or your own garage, with step-by-step instructions, what to watch out for, and an honest section on when buying is the better call.

Quick answer

  • Easiest build: a low cube shelf on its side, a sanded plywood top and a thin wood lip. Built-in storage, under an hour of work.
  • No-build option: a rimmed tray with a non-slip liner on a kids table you already own.
  • Sturdiest build: a plywood-and-2x4 bench with a lower shelf, best for kids who will pound hard or move to real tools later.
  • Set the height by measuring your child, not by age: the top should land between their waist and bent elbow.
  • Safety basics: no tipping, no splinters, no exposed screw heads, no pinch points, and no small parts for children under 3.
  • Buy instead if you rent, lack tools, need it this week, or would have to buy all the tools for the bench anyway.

What a DIY kids workbench needs to do

A kids workbench is a stable, child-height work surface where children can hammer, twist, sort and build, with their tools stored within reach. That definition sounds simple, but it hides five jobs that a good homemade bench has to do well.

  1. Fit the child. Too low and they hunch. Too high and they work with arms raised, which tires them out fast and makes tools harder to control.
  2. Stay still. Kids lean, push, climb and pound. A bench that wobbles or tips is the most common way a homemade project goes wrong.
  3. Be safe to touch. Rounded corners, sanded faces, no splinters, no screw points, no gaps that pinch.
  4. Contain the mess. Bolts and nuts roll. A raised lip on three sides saves a lot of crawling under the couch.
  5. Store the tools. If the tools live somewhere else, the bench gets used less. Storage under or above the surface makes it a self-contained place to play.

Why go to the trouble at all? The American Academy of Pediatrics clinical report “The Power of Play” describes play as central to children’s development, including the hands-on, self-directed kind that a workbench invites. NAEYC also emphasizes giving young children real materials and space for open-ended play. A dedicated spot tells a child that building is something they’re welcome to do any time.

Before you build: measure, plan and pick a spot

A few minutes of planning saves you from the most common regret with any DIY kids workbench: building it at the wrong height or for the wrong room.

Measure your child, not the age chart

Have your child stand in the shoes they usually wear indoors. Measure from the floor to their waist, then from the floor to their elbow when it’s bent at a right angle. Your finished work surface should land between those two numbers. Lower in that range suits hammering, since kids swing down onto the work. Higher suits detail work like screwing bolts and sorting small pieces.

Children grow quickly, so many parents build toward the top of the range and add a wide, sturdy step platform that can be removed later. Another approach is to design legs you can lengthen with bolted-on blocks. Our kids workbench height guide walks through this in more detail, including how to adjust for siblings of different sizes.

Choose where it will live

Measure the space before you measure lumber. A bench against a wall feels stable and keeps tools organized, while a bench with open sides lets two kids work at once. Keep it away from windows with blind cords, heaters and high-traffic doorways. For room-by-room ideas, see kids workbench setup and where to put it.

Decide who will use it

  • One toddler: a smaller, lower surface is fine, and simpler is better.
  • Siblings: plan for width. Two kids side by side need noticeably more room than one, plus two sets of storage.
  • A child who will grow into real tools: build heavier now so the bench can handle real pounding later.

7 DIY kids workbench ideas from common materials

Here’s how the seven builds compare. Pick the one that matches your tools, your time and your child’s age.

Build Skill level Time Best ages Main materials
Cube shelf on its side Beginner Under an hour 2 to 7 Low cube shelf, plywood top, trim strip
Two crates and a plank Beginner About an hour 3 to 7 Wooden crates, solid board, screws
Cut-down table with a lip Beginner to intermediate An afternoon 3 to 8 Sturdy wood table, trim, saw
Tabletop tray bench No building Minutes 3 to 8 Rimmed tray, non-slip liner
Cardboard box bench Beginner An afternoon with your child 2 to 4 Heavy box, packing tape, tubes
Plywood and 2x4 bench Intermediate A weekend 3 to 10 Plywood, 2x4s, screws, glue
Wall-mounted fold-down bench Intermediate A weekend 4 to 10 Plywood, locking folding brackets, pegboard

1. Cube shelf turned on its side

This is the easiest sturdy build. A low two-cube or three-cube shelf turned on its side becomes a long, low base with cubbies facing out, and a plywood top turns it into a real work surface.

What you need:

  • A solid, fully assembled low cube shelf
  • A piece of 3/4-inch plywood cut to the shelf’s footprint plus a small overhang
  • A 1x2 or similar thin strip for the lip
  • Wood screws, wood glue, a drill and medium and fine sandpaper
  • Fabric or plastic bins that fit the cubes

How to make it:

  1. Turn the shelf on its side and check that it sits flat without rocking. Shim or sand the feet if needed.
  2. Cut the plywood so it overhangs by only a small amount on each side. A big overhang creates a lever that can tip the bench when a child leans on the edge.
  3. Round all four corners of the top with a jigsaw or sandpaper, then sand every edge smooth.
  4. Screw the top down through the shelf’s top panel from below, so no screw heads face up.
  5. Glue and screw a thin strip along the back and both short sides to form a lip.
  6. Finish with a water-based clear coat, let it cure fully, then add bins.

Watch out for: Flat-pack shelves are designed to stand upright. On their side, the panels carry weight differently, so press down hard on the center and push on the ends before trusting it. Screwing the top on helps tie the whole unit together.

2. Two crates and a plank

Wooden crates from a craft store make a charming, open-sided bench with storage at each end.

What you need:

  • Two sturdy wooden crates of the same size
  • A solid board such as a wide pine plank or a piece of plywood
  • A thin back brace board, screws, a drill and sandpaper

How to make it:

  1. Stand the crates on end, open sides facing out, spaced so the plank spans them with a small overhang.
  2. Check the height. If it’s too low, add a solid wood base under each crate and screw it in.
  3. Screw a brace across the back of both crates so they can’t spread apart.
  4. Screw the plank down from inside the crates.
  5. Sand everything, especially the crate slats, which are often rough.

Watch out for: Craft crates vary a lot in quality. Thin slats, staples and loose bottoms aren’t built for kids sitting on or kicking them. Pull or hammer flat any staples, and replace weak bottoms with plywood.

3. Cut-down kids table or side table with a lip

A thrift-store side table or an older kids table can become a workbench with a few cuts and a raised edge.

What you need:

  • A solid wood table with four sturdy legs and no glass
  • A handsaw or miter saw, a measuring tape, a pencil and a level
  • Trim or a 1x2 strip for the lip, plus a scrap board for a lower shelf if you want one

How to make it:

  1. Decide on the final height from your measurements and subtract it from the current height to get the amount to remove.
  2. Mark every leg from the floor up, not from the top down, since floors and tables are rarely perfect.
  3. Cut, set the table on a flat floor and check with a level. Sand the long legs a little at a time to fix any wobble.
  4. Add a lip on three sides.
  5. If the legs allow, screw a lower shelf between them. It adds storage and stiffens the frame.

Watch out for: Older painted furniture can contain lead-based paint. If you don’t know the paint’s history, use an inexpensive lead test kit or skip that piece. Also tighten every leg joint, since a wobble that’s mild for an adult becomes a real problem when a child pounds on the top.

4. Tabletop tray bench (no building required)

If you want a workbench this afternoon, a rimmed tray on a table your child already uses does most of the job.

What you need:

  • A large rimmed tray: a wooden serving tray, a sturdy boot tray or a baking sheet with no sharp edges
  • Non-slip shelf liner cut to fit, under and inside the tray

How to set it up:

  1. Place a layer of non-slip liner on the table and set the tray on top.
  2. Line the inside of the tray so bolts don’t bounce and clatter.
  3. Keep a small bin of tools beside it, and store the whole setup on a shelf when play is done.

Watch out for: Height. Coffee tables are usually too low for standing and about right for kneeling, which some kids prefer. Avoid trays with thin metal rims that could have sharp corners.

This setup works especially well in apartments, and it’s a good way to test whether your child will actually use a bench before you build anything bigger.

5. Cardboard box bench for toddlers

A big cardboard box is the classic toddler pretend-play bench. It won’t last forever, but making it together is half the fun.

What you need:

  • A heavy-duty box, such as a large moving box
  • Packing tape and markers or washable paint
  • Paper towel tubes, a shoebox lid and other large, lightweight extras

How to make it:

  1. Tape the box closed and reinforce every edge with packing tape.
  2. Fill the bottom with a few heavy books wrapped in a bag so the box doesn’t slide.
  3. Draw a pegboard outline on the back panel and “hang” chunky toy tools with large tape loops.
  4. Tape paper towel tubes along the sides as pretend pipes.
  5. Let your child color and decorate it.

Watch out for: Anything glued or taped on can come loose, and toddlers mouth things. For children under 3, every add-on needs to be large enough that it isn’t a choking risk. The CPSC’s small parts rules exist for exactly this reason, and our guide to the small parts choking hazard rule explains how to check items at home. Skip bottle caps, buttons and other small decorations.

6. Classic plywood and 2x4 workbench

This is the build to choose if you want something that will survive years of hard use and possibly real tools later on.

What you need:

  • 3/4-inch plywood for the top and a lower shelf
  • 2x4s for legs and the frame (called aprons)
  • 2.5-inch wood screws, wood glue, a drill, a saw, a square and sandpaper
  • Optional: a short piece of pegboard and a back rail

How to make it:

  1. Size the top. A top about 18 to 24 inches deep and as wide as your space allows works well for one or two kids. Deeper than that and small arms can’t reach the back.
  2. Cut the legs. Leg length equals your target height minus the thickness of the top.
  3. Build two side frames. Join each pair of legs with a short 2x4 near the top and another near the bottom, glued and screwed.
  4. Connect the frames with long 2x4 aprons front and back at the top, and rails at the bottom to hold the lower shelf.
  5. Check for square by measuring both diagonals. They should match.
  6. Add the top and shelf. Pre-drill and countersink every screw so the heads sit below the surface.
  7. Finish the details. Round all corners, sand every face, add a back rail with pegboard if you like, then apply a water-based finish.

Watch out for: Weight. This bench is heavy, which is good for stability but means pinched fingers if a child tries to slide it. Pre-drill near board ends to prevent splitting, and keep the lower shelf high enough that small feet can’t get trapped underneath.

7. Wall-mounted fold-down bench with pegboard

For small homes, a bench that folds flat against the wall gives you a full work surface without giving up floor space.

What you need:

  • A plywood top
  • Heavy-duty folding shelf brackets that lock in the open position
  • A pegboard panel with spacers and mounting screws
  • A stud finder, a level and lag screws long enough to reach well into the studs

How to make it:

  1. Find and mark the studs. Never rely on drywall anchors alone for a surface a child will lean and pound on.
  2. Mount the brackets into the studs at your target height and check that they’re level.
  3. Attach the top, rounding the corners first.
  4. Mount pegboard above, on spacers so hooks can seat properly.
  5. Hang tools and small bins on the pegboard, keeping hooks above your child’s head height where possible, so nothing pokes at eye level.

Watch out for: Pinch points at the brackets. Choose brackets with a positive lock, and make opening and closing an adult-only job. Loose pegboard hooks can pull out and fall, so use hooks that lock in or swap them for small bins.

Materials and finishes: what to use and what to skip

The material you choose shapes how safe and long-lasting your bench will be. This table covers the materials parents ask about most.

Material Good for Notes
Plywood with smooth faces Tops, shelves Flat and strong. Sand the edges well, since plies can splinter.
Solid pine Legs, frames, lips Easy to cut and sand. Soft, so it will dent, which is fine for a kids bench.
MDF Tops in light-use builds Very smooth, but swells if it gets wet and is dusty to cut. Seal every edge.
Pallet wood Rustic accents only Unknown history. Look for a heat-treated stamp and skip stained or oily boards.
Pressure-treated lumber Outdoor structures, not kid furniture Made for weather and ground contact. Choose untreated wood for anything kids handle.
Old painted furniture Bases, if the paint checks out Older paint may contain lead. Test it or skip it.

Finishes

A finish protects the wood and makes it easier to wipe clean. Choose a water-based paint or clear coat, apply thin coats, and let it cure for the full time listed on the label. Cure time is usually longer than dry-to-touch time, and the smell fading is a good sign it’s ready. If a product mentions suitability for toys or children’s furniture on its label, read those instructions carefully.

Hardware

Use screws rather than nails for anything structural, since screws hold better when kids pull and push on a joint. Countersink every screw, and run a hand over every surface after assembly. If your palm catches on anything, sand it or fix it.

DIY kids workbench safety checklist

A homemade bench doesn’t come with a manufacturer’s safety testing, so you are the safety tester. The CPSC’s toy safety guidance and Nemours KidsHealth’s advice on choosing safe toys both stress checking for sharp edges, points and small parts, and that’s a good starting framework for anything a child plays with daily.

Run through this list before the first play session and again every month or so:

  • No tipping: the bench stays planted when pushed from any side and when a child leans on the front edge.
  • No splinters: every surface is sanded, including undersides small hands reach.
  • No hardware sticking out: screws are countersunk and no points come through the back of any board.
  • Rounded corners: especially on the top, which often sits at a toddler’s face height.
  • No pinch points: no unlocked hinges, folding legs or lids that can slam.
  • Right-sized parts: nothing small enough to choke on for children under 3, including decorations and loose hardware.
  • Anchored when needed: anything tall or wall-mounted is secured into studs.
  • Clear surroundings: no blind cords, heaters or stairs right next to the bench.
  • Safety glasses on: a habit worth starting early, even with toy tools.
  • An adult nearby: for younger kids, within arm’s reach.

For a fuller picture of tool rules, supervision and age-specific risks, read our kids tool set safety guide.

The 60-second push test

Before your child uses the bench, stand in front of it and press down hard on the front edge, then push it firmly from the side, then pull on it from the front as a climbing child might. Next, lean on each corner. If anything shifts, creaks, racks sideways or lifts, fix it before play starts. Repeat the test whenever you move the bench or notice a new wobble.

Building the workbench together

The build itself can be your child’s first project. Even small kids can do real parts of the work when you choose jobs to match their age, and they tend to use a bench more when they helped make it.

Jobs for ages 2 to 3

  • Choosing the paint color or the bins
  • Handing you screws from a cup you control
  • Decorating a cardboard bench with markers or stickers
  • Wiping down the finished surface

Jobs for ages 4 to 6

  • Holding one end of the tape measure and calling out numbers
  • Sanding flat surfaces with a sanding block, safety glasses on
  • Painting with a wide brush and water-based paint
  • Testing the finished bench for wobbles and reporting back

Jobs for ages 7 and up

  • Measuring and marking cut lines with you checking
  • Driving screws with a drill while you hold the work
  • Planning where each tool will be stored
  • Doing the monthly safety check with you

Talk through what you’re doing as you go: why you measure twice, why a lip stops bolts rolling, why the diagonals have to match. That turns a weekend project into a gentle lesson in measurement and planning, and it shows that grown-ups make mistakes and fix them too.

Stocking the bench: tools, parts and storage

A homemade bench arrives empty. What you put on it determines whether it gets used every day or becomes a place to pile laundry.

What belongs on a kids workbench

  • Core tools: a hammer, screwdrivers, a wrench and something to measure with.
  • Building parts: bolts, nuts, beams and gears so there’s always something to make.
  • Safety glasses: kid-sized and kept on the bench so they’re always within reach.
  • Sorting containers: a few small trays or bins so parts have a home.
  • Project ideas: a clipboard with simple pictures of things to build.

The easiest way to cover all of this at once is a complete kids tool set rather than collecting tools piece by piece. If you’ve built the bench and need everything to go on it, the BuildBox kids tool set includes a hammer, wrench, calipers, ruler, kid-safe knife, screwdriver set, builder safety glasses and 130+ bolts, nuts, beams, gears and shapes, plus an electric hand drill that really drives the bolts. It’s for ages 3 and up, since it contains small parts.

Storage that keeps the bench inviting

Less on the surface means more play. Keep only a few tools out at a time, store the rest in labeled bins, and rotate every week or two. Picture labels help pre-readers put things back. Our kids tool storage ideas cover bins, pegboard layouts and cleanup routines that actually stick.

Real tools vs toy tools

A sturdy homemade bench can eventually host real tools, but readiness depends on the child’s focus, coordination and ability to follow rules, not just age. Most families start with toy tools and move to one real tool at a time with close supervision. See when kids can use real tools for signs of readiness and a sensible order to introduce them. If real tools are the plan, build the plywood-and-2x4 bench, since lighter builds aren’t designed for real pounding.

When buying is better than building

Building a DIY kids workbench is rewarding, but it isn’t always the best choice. Here’s an honest look at both sides.

Building makes more sense when

  • You enjoy woodworking and already own the tools.
  • You want a large, permanent piece of furniture sized exactly for your space.
  • You have materials to reuse, like a spare cube shelf or leftover plywood.
  • Your child is old enough to help, and the project itself is part of the point.
  • You plan to move toward real tools and want a heavy, purpose-built bench.

Buying makes more sense when

  • You don’t have tools or a place to cut wood. Buying a saw and drill just for one project changes the math quickly.
  • You rent. Wall-mounted builds may not be allowed, and freestanding builds are hard to move.
  • You need it soon. A birthday next week doesn’t leave a weekend for building plus a full cure time for the finish.
  • You’d have to buy all the tools anyway. A bench without tools isn’t much fun, so the bench is only half the job.
  • You need two. Siblings often want their own space, which doubles the build.
  • It needs to travel. Visits to grandparents or a shared custody schedule favor something portable.

Ready-made options come in a few styles. Freestanding wooden and plastic tool benches from established toy brands suit families who want a permanent play-furniture piece without building it; check the current listing for sizes and age ranges, and see our comparison of wooden vs plastic tool benches if you’re weighing materials.

The other approach is a toolbox that turns into a workbench, which combines the bench and the tools in one box that packs away when play is done. The Thoson BuildBox works this way: a 152-piece set in a toolbox that opens into a workbench and a seat, with nothing to assemble and everything packing back inside. It’s $69 (was $109), or two full sets for $119 if siblings each need their own, with a choice of Blue or Pink for each box. A large, built-in wooden bench will suit a family with a dedicated playroom better, while a fold-away box suits smaller homes and families who move play around the house.

Build vs buy at a glance

Factor DIY workbench Ready-made freestanding bench Toolbox that opens into a bench
Upfront cost Low if you reuse materials and own tools, higher if you buy everything Check the current listing BuildBox: $69
Time to first play An hour to a weekend, plus finish cure time Delivery plus any assembly Delivery, nothing to assemble
Tools included No Varies by product Yes, in the BuildBox
Customized size Fully Fixed Fixed
Storage when not in use Stays out Stays out Packs away
Good for renters Freestanding builds only Yes Yes
Can grow into real tools Yes, if built sturdy Usually not designed for it No, designed for toy tool play

Neither option is “right” for everyone. A family with a garage, a free weekend and an older child who wants to help will get a lot out of building. A family in a two-bedroom apartment with a 4-year-old turning 5 next week will likely be happier buying.

Keeping a homemade workbench useful as kids grow

A well-built DIY kids workbench can last for years if you plan for growth and keep up with small maintenance.

Raise the height

  • Bolt-on leg extensions: add blocks of 2x4 to the bottom of each leg, glued and screwed, and recheck for level.
  • Remove the step platform you built in at the start.
  • Swap the legs entirely on the plywood-and-2x4 design, which is easy since the frame is modular.
  • Move the brackets up on a wall-mounted bench, reusing the same studs.

Change what’s on it

As kids move from pretend play to building to real projects, the bench should change too. Swap chunky toy tools for a more detailed set, add a pegboard section for their own organizing system, and give older kids a small project notebook. If you add a real vise later, mount it at the end where it won’t be in the way, and keep its use supervised.

Simple maintenance

  • Tighten screws and joints every few months, since daily pounding loosens them.
  • Re-sand any spot where the finish wears through or the wood gets rough.
  • Refresh the finish once a year or when it starts to look dull.
  • Repeat the push test after any repair or move.

A homemade bench that fits your child, stays steady and holds their tools within reach becomes the place they head when they want to make something. Whether you build it this weekend or buy one that opens up in minutes, the goal is the same: a safe, inviting spot where small hands get to do real work.

Frequently asked questions

How tall should a kids workbench be?

Measure your child rather than relying on an age chart. Have them stand in shoes, then measure from the floor to their waist and from the floor to their bent elbow. A good work surface sits between those two marks, so they can hammer and twist without hunching or reaching up. Many parents build a little taller and add a sturdy, wide step platform that comes out as the child grows.

What is the best wood for a DIY kids workbench?

Smooth plywood with good faces, such as birch plywood, makes a flat, strong top that resists warping. Solid pine works well for legs and frames and is easy to sand. Both take a water-based finish nicely. Skip pressure-treated lumber for indoor kid furniture, and be cautious with reclaimed or painted wood unless you know where it came from. Sand every edge and round the corners before a child uses it.

Is it safe to make a kids workbench out of pallets?

Pallets can work, but they are the riskiest common material. You often do not know how the wood was treated or what was spilled on it during shipping. If you use one, look for a stamp showing it was heat treated, avoid pallets that are stained, oily or marked as chemically treated, and sand thoroughly. For a first build, new pine or plywood is simpler and more predictable.

What age is a kids workbench good for?

Many children start enjoying a workbench around ages 2 to 3, mostly for pretend play with chunky toy tools. Kids around 3 to 6 get the most out of one, using it for building, sorting bolts and simple projects. Older children can use a sturdier bench for real woodworking with close adult supervision. Match what goes on the bench to the child's age, especially when small parts are involved.

What is the easiest DIY kids workbench to make?

The easiest option is a low cube shelf turned on its side with a sanded plywood top screwed on and a thin wood strip along the back and sides to stop parts rolling off. It needs only a drill, a few screws and sandpaper, and the cubes become built-in storage. An even simpler no-build option is a rimmed tray with a non-slip liner set on an existing kids table.

What paint or finish is safe for a homemade kids workbench?

Choose a water-based paint or clear finish and read the label for any notes about use on toys or children's furniture. Apply thin coats and let the finish cure fully for the time the manufacturer lists, which is often longer than the dry-to-touch time. Avoid old cans of paint of unknown origin and never reuse old painted furniture without checking the paint first.

Is it cheaper to build or buy a kids workbench?

Building is usually cheapest when you already own the tools and can reuse materials like a cube shelf or leftover plywood. If you have to buy lumber, hardware, sandpaper, finish and a drill, the total can end up close to a ready-made option, plus a weekend of your time. A homemade bench also arrives empty, so remember to budget for the tools that go on it.

What should I put on a kids workbench?

Start with an age-appropriate kids tool set: a hammer, screwdriver, wrench, measuring tools and a supply of bolts, nuts and beams to build with. Add kid-sized safety glasses, a few bins or trays for sorting, and a clipboard with simple project ideas. Keep only what the child can use well and rotate the rest so the bench stays inviting rather than cluttered.

How do I make a toddler workbench safe?

Keep it low and wide so it cannot tip, round every corner, sand out splinters and make sure no screw heads stick up. Use only large toy pieces for children under 3, since small parts are a choking hazard. Avoid hinges, folding legs and lids that can pinch fingers. Place it away from windows and cords, and stay close by during play.

Can kids use real hammers and nails at a DIY workbench?

Some families introduce real tools around early elementary age, but readiness depends on the child's focus, coordination and ability to follow safety rules, not just age. Start with one tool, a lightweight hammer and short nails into soft wood, with safety glasses on and an adult right beside them. Build the bench sturdy enough for real pounding before moving beyond toy tools.

Kids Tool Sets editorial team. We write practical, no-hype guides to kids tool sets, workbenches and screen-free play, built on public safety guidance and what parents tell us. How we work.

References and sources

  1. U.S. Consumer Product Safety Commission: Toys Safety Guide
  2. CPSC: Small Parts Ban and Choking Hazard Labeling
  3. NAEYC: Play
  4. Nemours KidsHealth: Choosing Safe Toys
  5. Yogman et al., The Power of Play, Pediatrics (AAP clinical report, 2018)

A kids tool set that turns into a workbench

152 pieces, a real working drill and a toolbox that opens into a bench and seat. $69 (was $109), or two for $119. Free US shipping.

See the BuildBox